Fantastic kit that is really fun! Contrary to the construction instructions you should take longer screws for the cardan shafts - the 1005 out of the kit. I have extended the wheelbase with the links of the OH35P01 (only at the front axle). I think that the Brouncer looks really good with it! All in all a super made kit - the final result is excellent! ----------- - use Fantastic kit that is really fun! Contrary to the instructions, you should use longer screws for the cardan shafts-the 1005s from the kit. I have lengthened the wheelbase with the links of the OH35P01 a little(only on the front axle). I think the Brouncer looks really good with it! All in all a well-made kit-the end result is excellent!

Fantastischer Bausatz der richtig Spaß macht! Entgegen der Bauanleitung sollte man längere Schrauben für die Kardanwellen nehmen - die 1005er aus dem Bausatz. Ich habe den Radstand mit den Links vom OH35P01 etwas verlängert (nur an der Vorderachse). Ich finde, dass der Brouncer damit richtig gut aussieht! Alles in allem ein super gemachter Bausatz - das Endergebnis ist hervorragend! ----------- Fantastic kit that is really fun! Contrary to the instructions, you should use longer screws for the cardan shafts - the 1005s from the kit. I have lengthened the wheelbase with the links of the OH35P01 a little (only on the front axle). I think the Brouncer looks really good with it! All in all a well-made kit - the end result is excellent!

Fantastic kit that is really fun! Contrary to the construction instructions you should take longer screws for the cardan shafts - the 1005 out of the kit. I have extended the wheelbase with the links of the OH35P01 (only at the front axle). I think that the Brouncer looks really good with it! All in all a super made kit - the final result is excellent! ----------- - use Fantastic kit that is really fun! Contrary to the instructions, you should use longer screws for the cardan shafts-the 1005s from the kit. I have lengthened the wheelbase with the links of the OH35P01 a little(only on the front axle). I think the Brouncer looks really good with it! All in all a well-made kit-the end result is excellent!

One thing to note about this Orlandoo is that banggood does not sell it's tires separate, and the upgrade rims are all to small for it, as it has bigger rims then all other ornadoo's. also the standard rim Weights does not fit, so make sure to choose the ones saying "18mm outer Diameter" !!! Most photos I took is after pimping it out. Added plastic panels to it with glue. I cut it from an old RC body. I drilled a 15mm hole in standard rims to fit inside them other orlandoo rims (giving it +-3.5mm wider Axles that helps it from rolling over). Also added custom Shocks i made from Nine eagle chopper parts. Changed the position of the arms holding axles as well and removed the center piece where it was held to give it more clearance. The shock towers at the front was also made out of helicopter spares, it was part of the servo in Nine eagles mini chopper.

One thing to note about this Orlandoo is that banggood does not sell it's tires separate, and the upgrade rims are all to small for it, as it has bigger rims then all other ornadoo's. also the standard rim Weights does not fit, so make sure to choose the ones saying "18mm outer Diameter" !!! Most photos I took is after pimping it out. Added plastic panels to it with glue. I cut it from an old RC body. I drilled a 15mm hole in standard rims to fit inside them other orlandoo rims (giving it +-3.5mm wider Axles that helps it from rolling over). Also added custom Shocks i made from Nine eagle chopper parts. Changed the position of the arms holding axles as well and removed the center piece where it was held to give it more clearance. The shock towers at the front was also made out of helicopter spares, it was part of the servo in Nine eagles mini chopper.

One thing to note about this Orlandoo is that banggood does not sell it's tires separate, and the upgrade rims are all to small for it, as it has bigger rims then all other ornadoo's. also the standard rim Weights does not fit, so make sure to choose the ones saying "18mm outer Diameter" !!! Most photos I took is after pimping it out. Added plastic panels to it with glue. I cut it from an old RC body. I drilled a 15mm hole in standard rims to fit inside them other orlandoo rims (giving it +-3.5mm wider Axles that helps it from rolling over). Also added custom Shocks i made from Nine eagle chopper parts. Changed the position of the arms holding axles as well and removed the center piece where it was held to give it more clearance. The shock towers at the front was also made out of helicopter spares, it was part of the servo in Nine eagles mini chopper.

I am very satisfied, the parts are of very good quality. The assembly is done without any problems. Great for the winter indoors

Je suis très satisfait, les pièces sont de très bonne qualité. le montage c’est fait sans aucun problème. super pour l’hiver à l’intérieur

I am very satisfied, the parts are of very good quality. The assembly is done without any problems. Great for the winter indoors

This is a super cool Ornaldoo model. Building the frame is not that difficult. But installing electronics and battery is a pain, there is not one word about it in the manual. I have built all Orlandoo models so far. This one is by far the most difficult one, only because of electronics install. Do NOT buy this as your first Orlandoo, it is really difficult to finish this model. 3 SMD LEDs in the back, 2 4 mm LEDs front, why again 4 mm Leds? I do have tons of 3 mm and 5 mm, but 4 mm are very hard to get and very expensive. I did have some from the Orlandoo ESCs. It is also very hard to find batterys, even 2s 180 mAh are already large. Finally I decided to use 2 1s 160 mAh packs in the side parts and connect those in series for a 2s Lipo. Check my build video, I will put it into the video section after finishing this build.

This is a super cool Ornaldoo model. Building the frame is not that difficult. But installing electronics and battery is a pain, there is not one word about it in the manual. I have built all Orlandoo models so far. This one is by far the most difficult one, only because of electronics install. Do NOT buy this as your first Orlandoo, it is really difficult to finish this model. 3 SMD LEDs in the back, 2 4 mm LEDs front, why again 4 mm Leds? I do have tons of 3 mm and 5 mm, but 4 mm are very hard to get and very expensive. I did have some from the Orlandoo ESCs. It is also very hard to find batterys, even 2s 180 mAh are already large. Finally I decided to use 2 1s 160 mAh packs in the side parts and connect those in series for a 2s Lipo. Check my build video, I will put it into the video section after finishing this build.

This is a super cool Ornaldoo model. Building the frame is not that difficult. But installing electronics and battery is a pain, there is not one word about it in the manual. I have built all Orlandoo models so far. This one is by far the most difficult one, only because of electronics install. Do NOT buy this as your first Orlandoo, it is really difficult to finish this model. 3 SMD LEDs in the back, 2 4 mm LEDs front, why again 4 mm Leds? I do have tons of 3 mm and 5 mm, but 4 mm are very hard to get and very expensive. I did have some from the Orlandoo ESCs. It is also very hard to find batterys, even 2s 180 mAh are already large. Finally I decided to use 2 1s 160 mAh packs in the side parts and connect those in series for a 2s Lipo. Check my build video, I will put it into the video section after finishing this build.

Second kit. Fabulous! I used a nanoricevator with an integrated 6A esc. It's a fairy tale!

Secondo kit. Favoloso! Ho usato un nanoricevitore con un esc integrato da 6A. Va una favola!

Second kit. Fabulous! I used a nanoricevator with an integrated 6A esc. It's a fairy tale!

If you want to break all your fingers, this kit is at the right place. Fun on the side, the model is really extremely small, but the construction of the model is a lot of fun. Everything fits together exactly and is of good quality. Only drawback, the supplied screwdriver and Allen wrenches are not really to use. I recommend the following tool for the construction. A high quality, MAGNETIC, ph0 screwdriver, Allen screwdriver, tweezers, nail file and if necessary. a magnet (to prevent the tiny screws from escaping). I painted the body as well as the rims with airbrush colours, which gives the model the last touch. Enjoy the crafting.

Wer sich einmal alle Finger brechen möchte ist mit diesem Bausatz an der richtigen Adresse. Spaß bei Seite, das Modell ist wirklich extrem klein, aber der Aufbau des Modells macht sehr viel Spaß. Alles passt exakt zusammen ums ist von guter Qualität. Einziges Manko, der mitgelieferte Schraubendreher und Inbusschlüssel sind nicht wirklich zu gebrauchen. Ich empfehle folgendes Werkzeug für den Aufbau. Ein hochwertiger, MAGNETISCHER, ph0 Schraubendreher, ein Inbusschraubendreher, eine Pinzette, eine Nagelfeile und ggf. ein Magnet (um die winzigen Schrauben an der Flucht zu hindern). Ich habe die Karosserie sowie die Felgen übrigens mit Airbrushfarben lackiert, was dem Modell den letzten touch verleiht. Viel Spaß beim Basteln.

If you want to break all your fingers, this kit is at the right place. Fun on the side, the model is really extremely small, but the construction of the model is a lot of fun. Everything fits together exactly and is of good quality. Only drawback, the supplied screwdriver and Allen wrenches are not really to use. I recommend the following tool for the construction. A high quality, MAGNETIC, ph0 screwdriver, Allen screwdriver, tweezers, nail file and if necessary. a magnet (to prevent the tiny screws from escaping). I painted the body as well as the rims with airbrush colours, which gives the model the last touch. Enjoy the crafting.

so far soooo great very nice made DIY

so far soooo great very nice made DIY

so far soooo great very nice made DIY

amazing tiny crawler, not yet finished but looks good!

amazing tiny crawler, not yet finished but looks good!

amazing tiny crawler, not yet finished but looks good!

The box has come deformed by its mispackaged. I'm in danger of breaking the contents.

La caja ha venido deformado por su mal empaquetado. Peligro que se rompa el contenido.

The box has come deformed by its mispackaged. I'm in danger of breaking the contents.

Super kit, absolutely fast and reliable delivery.

Super Kit, absolut schnelle und zuverlässige Lieferung.

Super kit, absolutely fast and reliable delivery.